Contents
Short Descriptions
adds or removes SCSI devices without having to reboot |
|
accesses Linux SCSI logging level information |
|
checks SCSI device support for mandatory commands |
|
does the SCSI READ CAPACITY command on disks |
|
does the SCSI TEST UNIT READY on devices |
|
checks for SCSI to ATA Translation (SAT) device support |
|
starts one or more SCSI disks |
|
stops one or more SCSI disks |
|
fetches the temperature of a SCSI device |
|
performs a SCSI BACKGROUND CONTROL command on a device to perform "advanced background operations" |
|
sends the SCSI COMPARE AND WRITE command to device |
|
sends the SCSI RECEIVE COPY RESULTS command (XCOPY related) |
|
copies data to and from files and devices. Specialised for devices that understand the SCSI command set |
|
takes SCSI sense data in binary or as a sequence of ASCII hexadecimal bytes and decodes it |
|
changes ownership of a LUN from another Service-Processor to this one |
|
formats or resizes a SCSI disk (perhaps changes its block size) |
|
sends a SCSI GET CONFIGURATION command (MMC-4 +) |
|
sends a SCSI GET PHYSICAL ELEMENT STATUS command to a device |
|
sends the SCSI GET LBA STATUS command |
|
sends a SCSI REPORT or SET IDENTIFYING INFORMATION command |
|
access mode page information for a SCSI (or ATAPI) device |
|
sends a SCSI INQUIRY or ATA IDENTIFY (PACKET) DEVICE command and outputs the response |
|
access log pages with SCSI LOG SENSE command |
|
sends the SCSI REPORT LUNS command |
|
displays mapping between linux sg and other SCSI devices |
|
maps a special file to a SCSI generic (sg) device (or vice versa) |
|
copies data to and from files and devices. Specialized for devices that understand the SCSI command set and does memory mapped transfers from sg devices |
|
reads mode pages with the SCSI MODE SENSE command |
|
reports information on supported SCSI commands or task management functions |
|
copies data to and from files and devices. Specialized for devices that understand the SCSI command set |
|
sends a SCSI PERSISTENT RESERVE (IN or OUT) command to manipulate registrations and reservations |
|
sends a SCSI PREVENT ALLOW MEDIUM REMOVAL command |
|
sends an arbitrary SCSI command to a device |
|
reads data using the SCSI READ BUFFER command |
|
displays or modifies the RDAC Redundant Controller Page |
|
reads blocks of data continually from the same offset |
|
performs a SCSI READ ATTRIBUTE command on a device |
|
sends a SCSI READ BLOCK LIMITS command |
|
sends a SCSI READ BUFFER command |
|
sends a SCSI READ CAPACITY command |
|
sends a SCSI READ LONG command |
|
sends a SCSI REASSIGN BLOCKS command |
|
sends a SCSI REPORT REFERRALS command |
|
sends a SCSI REPORT PROVISIONING INITIALIZATION PATTERN command |
|
sends a SCSI REPORT ZONES command |
|
sends one or more SCSI REQUEST SENSE commands |
|
sends a SCSI device, target, bus or host reset; or checks reset state |
|
sends a SCSI RESET WRITE POINTER command |
|
sends a SCSI READ MEDIA SERIAL NUMBER command |
|
sends a SCSI REPORT TARGET PORT GROUPS command |
|
fetches status information from a SCSI Accessed Fault-Tolerant Enclosure (SAF-TE) device |
|
sends a SCSI SANITIZE command |
|
sends an ATA IDENTIFY (PACKET) DEVICE command via a SCSI to ATA Translation (SAT) layer |
|
sends an ATA READ LOG EXT command via a SAT pass through to fetch log page 11h which contains SATA phy event counters |
|
sends an ATA READ LOG EXT command via a SCSI to ATA Translation (SAT) layer |
|
sends an ATA SET FEATURES command via a SCSI to ATA Translation (SAT) layer |
|
does a scan of sg devices (or given SCSI/ATAPI/ATA devices) and prints the results |
|
performs a SCSI SEEK or PRE-FETCH command on a device and it's cache |
|
performs a SCSI SEND DIAGNOSTIC command |
|
sends controls and fetches the current status from a SCSI Enclosure Services (SES) device |
|
sends microcode to a SCSI enclosure |
|
sends a SCSI START STOP UNIT command to start, stop, load or eject medium |
|
sends a SCSI SET TARGET PORT GROUPS command |
|
performs a SCSI STREAM CONTROL or GET STREAM STATUS command on a device to open or close an I/O stream |
|
sends a SCSI command to synchronize the cache |
|
tests the SCSI host adapter by issuing write and read operations on a device's buffer and calculating checksums |
|
reports or sets the timestamp on a SCSI device |
|
sends one or more SCSI TEST UNIT READY commands |
|
sends a SCSI UNMAP command |
|
invokes SCSI VERIFY command(s) on a block device |
|
fetches Vital Product Data (VPD) pages using a SCSI INQUIRY command |
|
sends a SCSI WRITE BUFFER command |
|
sends a SCSI WRITE LONG command |
|
sends a SCSI WRITE SAME command |
|
sends a SCSI WRITE AND VERIFY command |
|
performs SCSI WRITE commands on a device |
|
writes mode pages |
|
copies data to and from files and devices using SCSI EXTENDED COPY (XCOPY) |
|
performs SCSI ZONE commands on a device, such as OPEN, CLOSE, FINISH or SEQUENTIALIZE |
|
contains the sg3_utils API functions |