GDB-15.1

Introduction to GDB

GDB, the GNU Project debugger, allows you to see what is going on inside another program while it executes -- or what another program was doing at the moment it crashed. Note that GDB is most effective when tracing programs and libraries that were built with debugging symbols and not stripped.

This package is known to build and work properly using an LFS 12.2 platform.

Package Information

  • Download (HTTP): https://ftp.gnu.org/gnu/gdb/gdb-15.1.tar.xz

  • Download MD5 sum: 494e3beaac44e66367c3e443a4414529

  • Download size: 23 MB

  • Estimated disk space required: 806 MB (add 1.0 GB for docs; add 720 MB for tests)

  • Estimated build time: 0.9 SBU (add 0.4 SBU for docs; see below for tests; all using parallelism=8)

GDB Dependencies

Recommended Runtime Dependency

Optional

Doxygen-1.12.0, GCC-14.2.0 (ada, gfortran, and go are used for tests), Guile-3.0.10, rustc-1.80.1 (used for some tests), Valgrind-3.23.0, and SystemTap (run-time, used for tests)

Installation of GDB

Install GDB by running the following commands:

mkdir build &&
cd    build &&

../configure --prefix=/usr          \
             --with-system-readline \
             --with-python=/usr/bin/python3 &&
make

Optionally, to build the API documentation using Doxygen-1.12.0, run:

make -C gdb/doc doxy

Running the tests is not recommended. The results vary a lot depending on the system architecture and what optional dependencies are installed and what version of gcc is being used. On one system tested, there were 140 unexpected failures (out of over 108,000 tests) and on another system there were "only" 32 unexpected failures. The time to run the tests varies from approximately 6 SBU to over 15 SBU when using -j8. This depends on number of tests that time out as will as other factors.

[Tip]

Tip

With a plain make check, there are many warning messages about a missing global configuration file. These can be avoided by running touch global.exp and prepending the make check command with DEJAGNU=$PWD/global.exp. In addition the tests can be speeded up considerably by using the make option "-j<N>" where <N> is the number of cores on your system.

To test the results anyway, issue:

pushd gdb/testsuite &&
make  site.exp      &&
echo  "set gdb_test_timeout 30" >> site.exp &&
make check 2>1 | tee gdb-check.log
popd

See gdb/testsuite/README and TestingGDB. There are many additional problems with the test suite:

  • Clean directories are needed if re-running the tests. For that reason, make a copy of the compiled source code directory before the tests in case you need to run the tests again.

  • Results depend on installed compilers.

  • On some AMD-based systems, over 200 additional tests may fail due to a difference in the threading implementation on those CPUs.

Now, as the root user:

make -C gdb install &&
make -C gdbserver install

If you have built the API documentation, it is now in gdb/doc/doxy. You can install it (as the root user):

install -d /usr/share/doc/gdb-15.1 &&
rm -rf gdb/doc/doxy/xml &&
cp -Rv gdb/doc/doxy /usr/share/doc/gdb-15.1

Command Explanations

--with-system-readline: This switch forces GDB to use the copy of Readline installed in LFS.

--with-python=/usr/bin/python3: This switch forces GDB to use Python 3.

Contents

Installed Programs: gcore, gdb, gdbserver, and gdb-add-index
Installed Library: libinproctrace.so
Installed Directories: /usr/{include,share}/gdb and /usr/share/doc/gdb-15.1

Short Descriptions

gcore

generates a core dump of a running program

gdb

is the GNU Debugger

gdbserver

is a remote server for the GNU debugger (it allows programs to be debugged from a different machine)

gdb-add-index

Allows adding index files to ELF binaries. This speeds up gdb start on large programs.

libinproctrace.so

contains functions for the in-process tracing agent. The agent allows for installing fast tracepoints, listing static tracepoint markers, probing static tracepoints markers, and starting trace monitoring.