[blfs-support] Persistent device names problem.

pete peatches at blueyonder.co.uk
Fri Nov 2 10:16:20 PDT 2012


Hi,
I am not sure if this should be under LFS but it only showed up when I
was well into the BLFS build.

My PC is an x86 32bit m/c with a USB Cable Modem for the internet
and an ethernet connection to a second PC.

I have built LFS-7.2 (which includes udev-188 and kernel-3.5.2)
plus BLFS Xorg-7.7-1 and Firefox-15.0.1 which is all working
OK. The problem shows up when I boot up with the USB Cable Modem
connected.

On booting, the ethernet connection is named eth0 and the USB
Cable Modem is named eth1. This would be fine, but the file
/etc/udev/rules.d/70-persistent-net.rules which should
swap the names does not run, meaning the interfaces cannot be
configured.

If I disconnect the USB Cable Modem before booting, the ethernet
connection is named eth0 as before, but then (as expected) the file
/etc/udev/rules.d/70-persistent-net.rules runs and
renames it to eth1. I can then connect the USB Cable Modem,
start the interface with "ifup eth0" and everything works OK.

This system has been working OK using LFS-7.0, udev-173 and kernel-3.1.

It appears that when the USB Cable Modem is detected, something
prevents the file 70-persistent-net.rules from running.

Any suggestions on how to trace the problem would be appreciated.

Pete.

============================

Below I have added the dmesg outputs for booting with and without the
USB Cable Modem connected.

Dmesg WITHOUT USB Cable Modem Connected:
pci_bus 0000:00: resource 6 [io  0x8000-0xffff]
pci_bus 0000:00: resource 7 [io  0x03b0-0x03df]
pci_bus 0000:00: resource 8 [io  0x1c00-0x1c80]
pci_bus 0000:00: resource 9 [mem 0xfec80000-0xfecbffff]
pci_bus 0000:00: resource 10 [mem 0x000a0000-0x000bffff]
pci_bus 0000:00: resource 11 [mem 0xc0000000-0xefffffff]
pci_bus 0000:00: resource 12 [mem 0xf4000000-0xfe02ffff]
pci_bus 0000:01: resource 0 [io  0xb000-0xbfff]
pci_bus 0000:01: resource 1 [mem 0xfdf00000-0xfdffffff]
pci_bus 0000:01: resource 2 [mem 0xfde00000-0xfdefffff pref]
pci_bus 0000:01: resource 4 [io  0x0000-0x03af]
pci_bus 0000:01: resource 5 [io  0x03e0-0x0cf7]
pci_bus 0000:01: resource 6 [io  0x8000-0xffff]
pci_bus 0000:01: resource 7 [io  0x03b0-0x03df]
pci_bus 0000:01: resource 8 [io  0x1c00-0x1c80]
pci_bus 0000:01: resource 9 [mem 0xfec80000-0xfecbffff]
pci_bus 0000:01: resource 10 [mem 0x000a0000-0x000bffff]
pci_bus 0000:01: resource 11 [mem 0xc0000000-0xefffffff]
pci_bus 0000:01: resource 12 [mem 0xf4000000-0xfe02ffff]
pci_bus 0000:02: resource 0 [io  0xa000-0xafff]
pci_bus 0000:02: resource 1 [mem 0xf8000000-0xfbffffff]
pci_bus 0000:02: resource 2 [mem 0xe0000000-0xefffffff 64bit pref]
pci_bus 0000:03: resource 0 [io  0x9000-0x9fff]
pci_bus 0000:03: resource 1 [mem 0xfdd00000-0xfddfffff]
pci_bus 0000:03: resource 2 [mem 0xfdc00000-0xfdcfffff 64bit pref]
pci_bus 0000:04: resource 0 [io  0x8000-0x8fff]
pci_bus 0000:04: resource 1 [mem 0xfdb00000-0xfdbfffff]
pci_bus 0000:04: resource 2 [mem 0xfda00000-0xfdafffff 64bit pref]
NET: Registered protocol family 2
IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
TCP established hash table entries: 131072 (order: 8, 1048576 bytes)
TCP bind hash table entries: 65536 (order: 6, 262144 bytes)
TCP: Hash tables configured (established 131072 bind 65536)
TCP: reno registered
UDP hash table entries: 512 (order: 1, 8192 bytes)
UDP-Lite hash table entries: 512 (order: 1, 8192 bytes)
NET: Registered protocol family 1
RPC: Registered named UNIX socket transport module.
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
RPC: Registered tcp NFSv4.1 backchannel transport module.
ACPI: PCI Interrupt Link [LUBA] enabled at IRQ 11
PCI: setting IRQ 11 as level-triggered
ACPI: PCI Interrupt Link [LUB2] enabled at IRQ 5
PCI: setting IRQ 5 as level-triggered
pci 0000:02:00.0: Boot video device
PCI: CLS 64 bytes, default 64
Installing knfsd (copyright (C) 1996 okir at monad.swb.de).
NTFS driver 2.1.30 [Flags: R/W DEBUG].
msgmni has been set to 1764
Block layer SCSI generic (bsg) driver version 0.4 loaded (major 254)
io scheduler noop registered
io scheduler deadline registered
io scheduler cfq registered (default)
xz_dec_test: module loaded
xz_dec_test: Create a device node with 'mknod xz_dec_test c 253 0' and 
write .xz files to it.
Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
serial8250: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
00:09: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
lp: driver loaded but no devices found
Real Time Clock Driver v1.12b
Linux agpgart interface v0.103
parport_pc 00:0b: reported by Plug and Play ACPI
parport0: PC-style at 0x378, irq 7 [PCSPP(,...)]
lp0: using parport0 (interrupt-driven).
FDC 0 is a post-1991 82077
loop: module loaded
Uniform Multi-Platform E-IDE driver
amd74xx 0000:00:06.0: UDMA133 controller
amd74xx 0000:00:06.0: IDE controller (0x10de:0x03ec rev 0xa2)
amd74xx 0000:00:06.0: IDE port disabled
amd74xx 0000:00:06.0: not 100% native mode: will probe irqs later
     ide0: BM-DMA at 0xf000-0xf007
Probing IDE interface ide0...
hda: HL-DT-ST GCE-8520B, ATAPI CD/DVD-ROM drive
Refined TSC clocksource calibration: 2612.036 MHz.
Switching to clocksource tsc
hda: host max PIO5 wanted PIO255(auto-tune) selected PIO4
hda: UDMA/33 mode selected
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
ide_generic: please use "probe_mask=0x3f" module parameter for probing 
all legacy ISA IDE ports
ide-gd driver 1.18
ide-cd driver 5.00
ide-cd: hda: ATAPI 40X CD-ROM CD-R/RW drive, 2048kB Cache
cdrom: Uniform CD-ROM driver Revision: 3.20
sata_nv 0000:00:08.0: version 3.5
ACPI: PCI Interrupt Link [LSID] enabled at IRQ 11
sata_nv 0000:00:08.0: setting latency timer to 64
scsi0 : sata_nv
scsi1 : sata_nv
ata1: SATA max UDMA/133 cmd 0x9f0 ctl 0xbf0 bmdma 0xd800 irq 11
ata2: SATA max UDMA/133 cmd 0x970 ctl 0xb70 bmdma 0xd808 irq 11
ACPI: PCI Interrupt Link [LFID] enabled at IRQ 10
PCI: setting IRQ 10 as level-triggered
sata_nv 0000:00:08.1: setting latency timer to 64
scsi2 : sata_nv
scsi3 : sata_nv
ata3: SATA max UDMA/133 cmd 0x9e0 ctl 0xbe0 bmdma 0xc400 irq 10
ata4: SATA max UDMA/133 cmd 0x960 ctl 0xb60 bmdma 0xc408 irq 10
forcedeth: Reverse Engineered nForce ethernet driver. Version 0.64.
ACPI: PCI Interrupt Link [LMAC] enabled at IRQ 15
PCI: setting IRQ 15 as level-triggered
forcedeth 0000:00:07.0: setting latency timer to 64
ata3: SATA link down (SStatus 0 SControl 300)
ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
ata1.00: ATA-8: WDC WD5001AALS-00L3B2, 01.03B01, max UDMA/133
ata1.00: 976773168 sectors, multi 16: LBA48 NCQ (depth 0/32)
ata1.00: configured for UDMA/133
scsi 0:0:0:0: Direct-Access     ATA      WDC WD5001AALS-0 01.0 PQ: 0 ANSI: 5
sd 0:0:0:0: [sda] 976773168 512-byte logical blocks: (500 GB/465 GiB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't 
support DPO or FUA
forcedeth 0000:00:07.0: ifname eth0, PHY OUI 0x50ef @ 0, addr 
00:22:68:72:e6:a1
forcedeth 0000:00:07.0: highdma pwrctl mgmt lnktim msi desc-v3
usbcore: registered new interface driver kaweth
usbcore: registered new interface driver asix
usbcore: registered new interface driver cdc_ether
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
ehci_hcd 0000:00:02.1: setting latency timer to 64
ehci_hcd 0000:00:02.1: EHCI Host Controller
ehci_hcd 0000:00:02.1: new USB bus registered, assigned bus number 1
ehci_hcd 0000:00:02.1: debug port 1
ehci_hcd 0000:00:02.1: cache line size of 64 is not supported
ehci_hcd 0000:00:02.1: irq 5, io mem 0xfe02e000
ehci_hcd 0000:00:02.1: USB 2.0 started, EHCI 1.00
usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb1: Product: EHCI Host Controller
usb usb1: Manufacturer: Linux 3.5.2 ehci_hcd
usb usb1: SerialNumber: 0000:00:02.1
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 10 ports detected
ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
ohci_hcd 0000:00:02.0: setting latency timer to 64
ohci_hcd 0000:00:02.0: OHCI Host Controller
ohci_hcd 0000:00:02.0: new USB bus registered, assigned bus number 2
ohci_hcd 0000:00:02.0: irq 11, io mem 0xfe02f000
  sda: sda1 sda2 sda3 sda4 < sda5 sda6 sda7 sda8 sda9 sda10 >
sd 0:0:0:0: [sda] Attached SCSI disk
usb usb2: New USB device found, idVendor=1d6b, idProduct=0001
usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb2: Product: OHCI Host Controller
usb usb2: Manufacturer: Linux 3.5.2 ohci_hcd
usb usb2: SerialNumber: 0000:00:02.0
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 10 ports detected
uhci_hcd: USB Universal Host Controller Interface driver
usbcore: registered new interface driver cdc_acm
cdc_acm: USB Abstract Control Model driver for USB modems and ISDN adapters
usbcore: registered new interface driver usblp
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
usbcore: registered new interface driver microtekX6
i8042: PNP: PS/2 Controller [PNP0303:PS2K,PNP0f13:PS2M] at 0x60,0x64 irq 
1,12
serio: i8042 KBD port at 0x60,0x64 irq 1
serio: i8042 AUX port at 0x60,0x64 irq 12
mousedev: PS/2 mouse device common for all mice
cpuidle: using governor ladder
ACPI: PCI Interrupt Link [LAZA] enabled at IRQ 11
hda_intel: Disabling MSI
snd_hda_intel 0000:00:05.0: setting latency timer to 64
input: AT Translated Set 2 keyboard as 
/devices/platform/i8042/serio0/input/input0
ata2: SATA link down (SStatus 0 SControl 300)
ata4: SATA link down (SStatus 0 SControl 300)
TCP: cubic registered
NET: Registered protocol family 17
ALSA device list:
   #0: HDA NVidia at 0xfe024000 irq 11
input: ImExPS/2 Generic Explorer Mouse as 
/devices/platform/i8042/serio1/input/input1
EXT3-fs (sda5): mounted filesystem with writeback data mode
VFS: Mounted root (ext3 filesystem) readonly on device 8:5.
kjournald starting.  Commit interval 5 seconds
devtmpfs: mounted
Freeing unused kernel memory: 296k freed
systemd-udevd[1263]: starting version 188
systemd-udevd[1267]: renamed network interface eth0 to eth1
nvidia: module license 'NVIDIA' taints kernel.
Disabling lock debugging due to kernel taint
ACPI: PCI Interrupt Link [LNK8] enabled at IRQ 5
vgaarb: device changed decodes: 
PCI:0000:02:00.0,olddecodes=io+mem,decodes=none:owns=io+mem
NVRM: loading NVIDIA UNIX x86 Kernel Module  304.60  Sun Oct 14 20:13:08 
PDT 2012
Adding 9767516k swap on /dev/sda3.  Priority:1 extents:1 across:9767516k
EXT3-fs (sda5): warning: maximal mount count reached, running e2fsck is 
recommended
EXT3-fs (sda5): using internal journal
EXT3-fs (sda6): warning: maximal mount count reached, running e2fsck is 
recommended
kjournald starting.  Commit interval 5 seconds
EXT3-fs (sda6): using internal journal
EXT3-fs (sda6): mounted filesystem with writeback data mode
EXT3-fs (sda7): warning: maximal mount count reached, running e2fsck is 
recommended
kjournald starting.  Commit interval 5 seconds
EXT3-fs (sda7): using internal journal
EXT3-fs (sda7): mounted filesystem with writeback data mode
EXT3-fs (sda8): warning: maximal mount count reached, running e2fsck is 
recommended
kjournald starting.  Commit interval 5 seconds
EXT3-fs (sda8): using internal journal
EXT3-fs (sda8): mounted filesystem with writeback data mode
EXT3-fs (sda9): warning: maximal mount count reached, running e2fsck is 
recommended
kjournald starting.  Commit interval 5 seconds
EXT3-fs (sda9): using internal journal
EXT3-fs (sda9): mounted filesystem with writeback data mode
EXT3-fs (sda10): warning: maximal mount count reached, running e2fsck is 
recommended
kjournald starting.  Commit interval 5 seconds
EXT3-fs (sda10): using internal journal
EXT3-fs (sda10): mounted filesystem with writeback data mode

============================

Dmesg WITH USB Cable Modem Connected:
pci_bus 0000:01: resource 1 [mem 0xfdf00000-0xfdffffff]
pci_bus 0000:01: resource 2 [mem 0xfde00000-0xfdefffff pref]
pci_bus 0000:01: resource 4 [io  0x0000-0x03af]
pci_bus 0000:01: resource 5 [io  0x03e0-0x0cf7]
pci_bus 0000:01: resource 6 [io  0x8000-0xffff]
pci_bus 0000:01: resource 7 [io  0x03b0-0x03df]
pci_bus 0000:01: resource 8 [io  0x1c00-0x1c80]
pci_bus 0000:01: resource 9 [mem 0xfec80000-0xfecbffff]
pci_bus 0000:01: resource 10 [mem 0x000a0000-0x000bffff]
pci_bus 0000:01: resource 11 [mem 0xc0000000-0xefffffff]
pci_bus 0000:01: resource 12 [mem 0xf4000000-0xfe02ffff]
pci_bus 0000:02: resource 0 [io  0xa000-0xafff]
pci_bus 0000:02: resource 1 [mem 0xf8000000-0xfbffffff]
pci_bus 0000:02: resource 2 [mem 0xe0000000-0xefffffff 64bit pref]
pci_bus 0000:03: resource 0 [io  0x9000-0x9fff]
pci_bus 0000:03: resource 1 [mem 0xfdd00000-0xfddfffff]
pci_bus 0000:03: resource 2 [mem 0xfdc00000-0xfdcfffff 64bit pref]
pci_bus 0000:04: resource 0 [io  0x8000-0x8fff]
pci_bus 0000:04: resource 1 [mem 0xfdb00000-0xfdbfffff]
pci_bus 0000:04: resource 2 [mem 0xfda00000-0xfdafffff 64bit pref]
NET: Registered protocol family 2
IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
TCP established hash table entries: 131072 (order: 8, 1048576 bytes)
TCP bind hash table entries: 65536 (order: 6, 262144 bytes)
TCP: Hash tables configured (established 131072 bind 65536)
TCP: reno registered
UDP hash table entries: 512 (order: 1, 8192 bytes)
UDP-Lite hash table entries: 512 (order: 1, 8192 bytes)
NET: Registered protocol family 1
RPC: Registered named UNIX socket transport module.
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
RPC: Registered tcp NFSv4.1 backchannel transport module.
ACPI: PCI Interrupt Link [LUBA] enabled at IRQ 11
PCI: setting IRQ 11 as level-triggered
ACPI: PCI Interrupt Link [LUB2] enabled at IRQ 5
PCI: setting IRQ 5 as level-triggered
pci 0000:02:00.0: Boot video device
PCI: CLS 64 bytes, default 64
Installing knfsd (copyright (C) 1996 okir at monad.swb.de).
NTFS driver 2.1.30 [Flags: R/W DEBUG].
msgmni has been set to 1764
Block layer SCSI generic (bsg) driver version 0.4 loaded (major 254)
io scheduler noop registered
io scheduler deadline registered
io scheduler cfq registered (default)
xz_dec_test: module loaded
xz_dec_test: Create a device node with 'mknod xz_dec_test c 253 0' and 
write .xz files to it.
Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
serial8250: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
00:09: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
lp: driver loaded but no devices found
Real Time Clock Driver v1.12b
Linux agpgart interface v0.103
parport_pc 00:0b: reported by Plug and Play ACPI
parport0: PC-style at 0x378, irq 7 [PCSPP(,...)]
lp0: using parport0 (interrupt-driven).
FDC 0 is a post-1991 82077
loop: module loaded
Uniform Multi-Platform E-IDE driver
amd74xx 0000:00:06.0: UDMA133 controller
amd74xx 0000:00:06.0: IDE controller (0x10de:0x03ec rev 0xa2)
amd74xx 0000:00:06.0: IDE port disabled
amd74xx 0000:00:06.0: not 100% native mode: will probe irqs later
     ide0: BM-DMA at 0xf000-0xf007
Probing IDE interface ide0...
hda: HL-DT-ST GCE-8520B, ATAPI CD/DVD-ROM drive
Refined TSC clocksource calibration: 2612.036 MHz.
Switching to clocksource tsc
hda: host max PIO5 wanted PIO255(auto-tune) selected PIO4
hda: UDMA/33 mode selected
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
ide_generic: please use "probe_mask=0x3f" module parameter for probing 
all legacy ISA IDE ports
ide-gd driver 1.18
ide-cd driver 5.00
ide-cd: hda: ATAPI 40X CD-ROM CD-R/RW drive, 2048kB Cache
cdrom: Uniform CD-ROM driver Revision: 3.20
sata_nv 0000:00:08.0: version 3.5
ACPI: PCI Interrupt Link [LSID] enabled at IRQ 11
sata_nv 0000:00:08.0: setting latency timer to 64
scsi0 : sata_nv
scsi1 : sata_nv
ata1: SATA max UDMA/133 cmd 0x9f0 ctl 0xbf0 bmdma 0xd800 irq 11
ata2: SATA max UDMA/133 cmd 0x970 ctl 0xb70 bmdma 0xd808 irq 11
ACPI: PCI Interrupt Link [LFID] enabled at IRQ 10
PCI: setting IRQ 10 as level-triggered
sata_nv 0000:00:08.1: setting latency timer to 64
scsi2 : sata_nv
scsi3 : sata_nv
ata3: SATA max UDMA/133 cmd 0x9e0 ctl 0xbe0 bmdma 0xc400 irq 10
ata4: SATA max UDMA/133 cmd 0x960 ctl 0xb60 bmdma 0xc408 irq 10
forcedeth: Reverse Engineered nForce ethernet driver. Version 0.64.
ACPI: PCI Interrupt Link [LMAC] enabled at IRQ 15
PCI: setting IRQ 15 as level-triggered
forcedeth 0000:00:07.0: setting latency timer to 64
ata3: SATA link down (SStatus 0 SControl 300)
ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
ata1.00: ATA-8: WDC WD5001AALS-00L3B2, 01.03B01, max UDMA/133
ata1.00: 976773168 sectors, multi 16: LBA48 NCQ (depth 0/32)
ata1.00: configured for UDMA/133
scsi 0:0:0:0: Direct-Access     ATA      WDC WD5001AALS-0 01.0 PQ: 0 ANSI: 5
sd 0:0:0:0: [sda] 976773168 512-byte logical blocks: (500 GB/465 GiB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't 
support DPO or FUA
forcedeth 0000:00:07.0: ifname eth0, PHY OUI 0x50ef @ 0, addr 
00:22:68:72:e6:a1
forcedeth 0000:00:07.0: highdma pwrctl mgmt lnktim msi desc-v3
usbcore: registered new interface driver kaweth
usbcore: registered new interface driver asix
usbcore: registered new interface driver cdc_ether
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
ehci_hcd 0000:00:02.1: setting latency timer to 64
ehci_hcd 0000:00:02.1: EHCI Host Controller
ehci_hcd 0000:00:02.1: new USB bus registered, assigned bus number 1
ehci_hcd 0000:00:02.1: debug port 1
ehci_hcd 0000:00:02.1: cache line size of 64 is not supported
ehci_hcd 0000:00:02.1: irq 5, io mem 0xfe02e000
ehci_hcd 0000:00:02.1: USB 2.0 started, EHCI 1.00
usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb1: Product: EHCI Host Controller
usb usb1: Manufacturer: Linux 3.5.2 ehci_hcd
usb usb1: SerialNumber: 0000:00:02.1
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 10 ports detected
ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
ohci_hcd 0000:00:02.0: setting latency timer to 64
ohci_hcd 0000:00:02.0: OHCI Host Controller
ohci_hcd 0000:00:02.0: new USB bus registered, assigned bus number 2
ohci_hcd 0000:00:02.0: irq 11, io mem 0xfe02f000
  sda: sda1 sda2 sda3 sda4 < sda5 sda6 sda7 sda8 sda9 sda10 >
sd 0:0:0:0: [sda] Attached SCSI disk
usb usb2: New USB device found, idVendor=1d6b, idProduct=0001
usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb2: Product: OHCI Host Controller
usb usb2: Manufacturer: Linux 3.5.2 ohci_hcd
usb usb2: SerialNumber: 0000:00:02.0
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 10 ports detected
uhci_hcd: USB Universal Host Controller Interface driver
usbcore: registered new interface driver cdc_acm
cdc_acm: USB Abstract Control Model driver for USB modems and ISDN adapters
usbcore: registered new interface driver usblp
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
usbcore: registered new interface driver microtekX6
i8042: PNP: PS/2 Controller [PNP0303:PS2K,PNP0f13:PS2M] at 0x60,0x64 irq 
1,12
serio: i8042 KBD port at 0x60,0x64 irq 1
serio: i8042 AUX port at 0x60,0x64 irq 12
mousedev: PS/2 mouse device common for all mice
cpuidle: using governor ladder
ACPI: PCI Interrupt Link [LAZA] enabled at IRQ 11
hda_intel: Disabling MSI
snd_hda_intel 0000:00:05.0: setting latency timer to 64
input: AT Translated Set 2 keyboard as 
/devices/platform/i8042/serio0/input/input0
ata2: SATA link down (SStatus 0 SControl 300)
ata4: SATA link down (SStatus 0 SControl 300)
usb 2-7: new full-speed USB device number 2 using ohci_hcd
usb 2-7: New USB device found, idVendor=069a, idProduct=0402
usb 2-7: New USB device strings: Mfr=1, Product=2, SerialNumber=3
usb 2-7: Product: USB Cable Modem
usb 2-7: Manufacturer: S-A
usb 2-7: SerialNumber: 00407B719BF3
cdc_ether 2-7:1.1: eth1: register 'cdc_ether' at usb-0000:00:02.0-7, CDC 
Ethernet Device, 00:40:7b:71:9b:f3
TCP: cubic registered
NET: Registered protocol family 17
ALSA device list:
   #0: HDA NVidia at 0xfe024000 irq 11
input: ImExPS/2 Generic Explorer Mouse as 
/devices/platform/i8042/serio1/input/input1
EXT3-fs (sda5): mounted filesystem with writeback data mode
VFS: Mounted root (ext3 filesystem) readonly on device 8:5.
kjournald starting.  Commit interval 5 seconds
devtmpfs: mounted
Freeing unused kernel memory: 296k freed
systemd-udevd[1268]: starting version 188
nvidia: module license 'NVIDIA' taints kernel.
Disabling lock debugging due to kernel taint
ACPI: PCI Interrupt Link [LNK8] enabled at IRQ 5
vgaarb: device changed decodes: 
PCI:0000:02:00.0,olddecodes=io+mem,decodes=none:owns=io+mem
NVRM: loading NVIDIA UNIX x86 Kernel Module  304.60  Sun Oct 14 20:13:08 
PDT 2012
Adding 9767516k swap on /dev/sda3.  Priority:1 extents:1 across:9767516k
EXT3-fs (sda5): warning: maximal mount count reached, running e2fsck is 
recommended
EXT3-fs (sda5): using internal journal
EXT3-fs (sda6): warning: maximal mount count reached, running e2fsck is 
recommended
kjournald starting.  Commit interval 5 seconds
EXT3-fs (sda6): using internal journal
EXT3-fs (sda6): mounted filesystem with writeback data mode
EXT3-fs (sda7): warning: maximal mount count reached, running e2fsck is 
recommended
kjournald starting.  Commit interval 5 seconds
EXT3-fs (sda7): using internal journal
EXT3-fs (sda7): mounted filesystem with writeback data mode
EXT3-fs (sda8): warning: maximal mount count reached, running e2fsck is 
recommended
kjournald starting.  Commit interval 5 seconds
EXT3-fs (sda8): using internal journal
EXT3-fs (sda8): mounted filesystem with writeback data mode
EXT3-fs (sda9): warning: maximal mount count reached, running e2fsck is 
recommended
kjournald starting.  Commit interval 5 seconds
EXT3-fs (sda9): using internal journal
EXT3-fs (sda9): mounted filesystem with writeback data mode
EXT3-fs (sda10): warning: maximal mount count reached, running e2fsck is 
recommended
kjournald starting.  Commit interval 5 seconds
EXT3-fs (sda10): using internal journal
EXT3-fs (sda10): mounted filesystem with writeback data mode

============================














More information about the blfs-support mailing list